more uptravel isn't going to get you any farther, so if you don't plan on installing drop brackets and adding taller springs to your spacers you might as well just drive it like it is until your springs start to sag, which they will soon enough if you do enough rough driving!  enjoy!

I'm not aware of anyone who is currently making or offering a set of springs for these things that will provide an honestl 2 or 2 1/2 inches of lift anyway.  So even if I go with longer springs, I'd still end up having to slide in a 1/2 inch or inch shim to push it to where it sits now.  If I went with longer springs and the smaller shim, I would probably pull off the sway bar and allow the arms to compress and flex easier.   Then again, if worms owned machineguns... those damned birds wouldn't screw with them so much either.  It's probably just as good they don't.

....   I might even opt for an OME spring set. 

That, you will not regret.

Which one would i not regret Ian, 1. not arming worms with machineguns.... or 2. pulling the coil spacers and installing longer springs and removing my sway bar?

Which one would i not regret Ian, 1. not arming worms with machineguns.... or 2. pulling the coil spacers and installing longer springs and removing my sway bar?

Opting for OME, as I said in the quote 

XJ coil measures: 17" tall, 5" dia. and uses 0.475" dia. wire
TJ coil measures: 18.5" tall, 5.25" dia. and uses 0.575" dia. wire
95 Aerostar coil measures:13.625" tall, 6.5" dia. and uses 0.600" dia. wire
2dr Kick rear measures: 12.5" tall, 4.25" dia. and uses 0.460" dia. wire
2dr Kick front measures: 10.875" tall, 4.375" dia. and uses 0.600" dia. wire

i got me a set of used xj springs off ebay for like $25 and it gave me another inch or so over the calmini springs, and the xj's can take a heavier load, for when ya load up for moab.

XJ coil measures: 17" tall, 5" dia. and uses 0.475" dia. wire
TJ coil measures: 18.5" tall, 5.25" dia. and uses 0.575" dia. wire
95 Aerostar coil measures:13.625" tall, 6.5" dia. and uses 0.600" dia. wire
2dr Kick rear measures: 12.5" tall, 4.25" dia. and uses 0.460" dia. wire
2dr Kick front measures: 10.875" tall, 4.375" dia. and uses 0.600" dia. wire

i got me a set of used xj springs off ebay for like $25 and it gave me another inch or so over the calmini springs, and the xj's can take a heavier load, for when ya load up for moab.

Did you use them on the front or rear?

Quote from: oilstained on February 15, 2008, 07:42:03 AM

XJ coil measures: 17" tall, 5" dia. and uses 0.475" dia. wire
TJ coil measures: 18.5" tall, 5.25" dia. and uses 0.575" dia. wire
95 Aerostar coil measures:13.625" tall, 6.5" dia. and uses 0.600" dia. wire
2dr Kick rear measures: 12.5" tall, 4.25" dia. and uses 0.460" dia. wire
2dr Kick front measures: 10.875" tall, 4.375" dia. and uses 0.600" dia. wire

i got me a set of used xj springs off ebay for like $25 and it gave me another inch or so over the calmini springs, and the xj's can take a heavier load, for when ya load up for moab.

Did you use them on the front or rear?

X2