Hello Guest

busted a crown vic rear shock into 2 pieces..

  • 18 Replies
  • 3226 Views

0 Members and 2 Guests are viewing this topic.

*

Offline beercheck

  • 1215
  • 0
  • Gender: Male
  • Go Cards!
    • trivia-nights.com
Re: busted a crown vic rear shock into 2 pieces..
« Reply #15 on: December 20, 2007, 01:55:31 PM »
i get the feeling my shock cracked when i had to get winched sideways when wedged between two stumps, it broke a couple hours after that happened.

Chuckling as I envision you using the shock as a recovery point.  Heh.
'03 ZR2 2dr Tracker, '02 XL-7 drivetrain and electrcs
XL-7 front coils
1.5" rear coil spacers
Monroe 32316 shocks w/2" extenders
235/70-16 Bridgestone Destination A/Ts on stock XL-7 Alloys RRO Rock Rails (Presently removed, as they rusted to all hell; all the bolts were rusted to dust.  Real nice, RRO...) http://www.trivia-nights.com

*

Offline bzzr2

  • 1011
  • 3
Re: busted a crown vic rear shock into 2 pieces..
« Reply #16 on: December 20, 2007, 05:12:11 PM »
LOL no, not quite, that would have been funny then just bad..  wish i had a pic from that stuck, i was pretty pissed at myself for getting to that point.. sometimes you just can't trust your spotters.  the winching wasn't quite directly sideways, we were able to use the recovery point on the back.

03-ZR2, 2dr, 31x10.5 SSR's & stuff...--sold :-(
03 xl7, jeff's 2inch spacer lift, 225/75/16's; sold
09 taco reg cab short box 4x4

*

Offline r3cc0s

  • 321
  • 0
  • Gender: Male
Re: busted a crown vic rear shock into 2 pieces..
« Reply #17 on: November 03, 2010, 09:32:41 PM »
has anyone ever come to a conclusions as to what is the best for coil lifts in our trucks?

I was using Munroe 550011s for a long time until the rubber wore out on the bottom bolt...

They were good until that happens, but I'd like to find a shock that extends that extra 2-3" inches while remaining close in compression with the same fittings...

I was thinking of ordering the pro-comps but curious what others are thinking... like the Ranchos?
03' 2.0L CAMI Tracker w/ 1.5" Front Spacers, 2" Rear Spacers, 1 & 1/4" poly-rubber rear spacer w/ hose clamps, Monroe Crown Vic interceptor rear shocks,1/4" bumpstop extenders, 1.5" strut Extenders, removal of sway bar and strut bar + plenty of cutting for 245/75/16 Goodyear MTRs

*

Offline bzzr2

  • 1011
  • 3
Re: busted a crown vic rear shock into 2 pieces..
« Reply #18 on: November 17, 2010, 01:52:13 PM »
80's model tbird shocks, this is after crown vics, mustangs and cavaliers on mine.  maybe not for a 2door but i run them on my xl7 and if i still had my 2dr i'd certainly be trying them~!
03-ZR2, 2dr, 31x10.5 SSR's & stuff...--sold :-(
03 xl7, jeff's 2inch spacer lift, 225/75/16's; sold
09 taco reg cab short box 4x4