Hello Guest
« previous next »
Pages: [1]   Go Down

SIDEKICK REAR DISC CONVERSION KIT

  • 8 Replies
  • 8560 Views

0 Members and 6 Guests are viewing this topic.

*

Offline 1BADKICK

  • 9
  • 0
  • Gender: Male
  • Member of the Jeep Recovery Team!!!
    • WWW.AMERICANMOBILEXRAY.COM
SIDEKICK REAR DISC CONVERSION KIT
« on: February 04, 2006, 08:42:27 PM »
DOES ANYONE MAKE A COMPLETE REAR DISC CONVERSION KIT FOR THE SIDEKICK?
Logged
*

Offline wildgoody

  • *
  • 8134
  • 67
  • Gender: Male
  • Turbocharged 150HP 1.6L 8V 93MPH 1/4 mile
Re: SIDEKICK REAR DISC CONVERSION KIT
« Reply #1 on: February 04, 2006, 10:21:44 PM »
Working on it, full floater and disk rear brakes
Logged
Real Trucks Are Built, Not Bought,
And Chrome Don't Get Ya Home.  

An armed man is a citizen. An unarmed man is a subject.
*

Offline Uncivilized

  • 1469
  • 1
  • Gender: Male
    • Car Domain
Re: SIDEKICK REAR DISC CONVERSION KIT
« Reply #2 on: February 04, 2006, 11:29:35 PM »
Quote from: wildgoody on February 04, 2006, 10:21:44 PM
Working on it, full floater and disk rear brakes

full floating axle...What does that mean?
Logged
*

Offline wildgoody

  • *
  • 8134
  • 67
  • Gender: Male
  • Turbocharged 150HP 1.6L 8V 93MPH 1/4 mile
Re: SIDEKICK REAR DISC CONVERSION KIT
« Reply #3 on: February 04, 2006, 11:58:04 PM »
The axle shaft supports no weight, the weight
is all supported by the axle housing.

This is the same setup as many 1 ton and 3/4
ton trucks, as well as all medium and heavy duty
trucks.

If you break an axle shaft, the wheel stays put,
doesn't come out or grind the axle shaft on the
housing inside.

 
Logged
Real Trucks Are Built, Not Bought,
And Chrome Don't Get Ya Home.  

An armed man is a citizen. An unarmed man is a subject.
*

Offline flexmonger

  • 209
  • 0
  • Gender: Male
  • live to wheel and wheel to die.
Re: SIDEKICK REAR DISC CONVERSION KIT
« Reply #4 on: February 05, 2006, 01:27:17 AM »
  Trail Tough has a kit to add rear disc breaks, but it would require a proportioning valve and a ebrake to finish.   check out: http://www.trailtough.com/images/samdiskbrk_small.jpg
« Last Edit: February 05, 2006, 01:31:05 AM by flexmonger »
Logged
*

Offline Chief

  • 678
  • 0
  • Gender: Male
  • Whaddya lookin at??
Re: SIDEKICK REAR DISC CONVERSION KIT
« Reply #5 on: February 05, 2006, 09:12:55 AM »
Quote from: flexmonger on February 05, 2006, 01:27:17 AM
  Trail Tough has a kit to add rear disc breaks, but it would require a proportioning valve and a ebrake to finish.   check out: http://www.trailtough.com/images/samdiskbrk_small.jpg


That's the kit I used for mine. Needs sammi calipers and I used the front discs off a tracker. I have a line lock for my e-brake, and am getting this setup for the proportioning valve and residual valve. click here

Line lock I am getting is this one.
Logged
03 Tacoma, BBP sliders, TRD L/S, Modded intake,  Da Tow Bitch

94 Tracker. Cancer mod :p Otherwise stock
*

Offline Rhinoman

  • 4502
  • 36
  • Gender: Male
  • Bend it, Break it, Fix it
    • Rhinoman
Re: SIDEKICK REAR DISC CONVERSION KIT
« Reply #6 on: February 05, 2006, 09:32:48 AM »
I have rear discs on mine with Ford calipers. To get them to work properly I had to fit a disc/disc master cylinder. The disc/drum m/c doesn't push enough fluid to the back brakes. The proportioning valve works to some extent but all it really does is restrict the flow to the rear brakes so you get less power from them. They seem to work OK on Samurai conversions with Zuk front calipers because they lock up the rears with the discs on the back. I had the opposite problem, the rear brakes were quite ineffective. Because its a tandem m/c the additional pedal travel made the front brakes come in much later and I ran out of pedal travel before I could get full power from the fronts.
Edit:
To add to that there are two different sizes of m/c and mine was the smaller one so this may be less of an issue with the bigger version.
« Last Edit: February 05, 2006, 09:52:08 AM by Rhinoman »
Logged
2000 Vitara 1.6, 3+3 Lift, 33"MTs, 5:83s, LWB brakes, Winch, Snorkel, Safari Rack
1986 SJ413K PickUp, 1.6L conversion.

OBD1 - Full diagnostics on a PC/Laptop: http://www.rhinopower.org
*

Offline Jimiweld

  • 234
  • 0
  • Gender: Male
    • www.fullfusion.ca
Re: SIDEKICK REAR DISC CONVERSION KIT
« Reply #7 on: October 10, 2006, 07:03:46 AM »
How do you set up e-brakes for the rear disc?
Jim
Logged
1990 Tracker - 3.5" body Lift, 1.5 coil spacers, 31" TRXUS tires, homemade front bumper, Automatic Tansmission, 5.12 diff gears. Rear is Locked
*

Offline Drone637

  • *
  • 8121
  • 116
  • Gender: Male
  • Evil Cow
Re: SIDEKICK REAR DISC CONVERSION KIT
« Reply #8 on: October 10, 2006, 11:02:09 AM »
You have to use a Line Lock or get a setup from a Subaru, which works if your using their calipers.  :)

With the Sammy you can just find an old SJ-410 E-brake kit or buy a driveline brake setup, I think Trail Tough makes it.  Not sure though.
Logged
96 Geo Tracker, x-SJ-410,  x-White Rabbit, x-Project Trouble
Crawlers NorthWest
x-Trouble Racing
Pages: [1]   Go Up
« previous next »