Hello Guest
« previous next »
Pages: [1]   Go Down

removal of rear tail shaft

  • 4 Replies
  • 1202 Views

0 Members and 1 Guest are viewing this topic.

*

Offline SiKiD_01

  • 574
  • 0
  • Gender: Male
  • Fully Sik, Flying Vit.
removal of rear tail shaft
« on: January 20, 2005, 01:07:08 PM »
i'm in the process of fitting a locker to my rear diff, and i'm going to get the uni joints in the rear tail shaft done too while i'm at it.

question is, when i take the shaft out of the gear box, do i need to mark it and install it back the same on the splines? i know of the sammy slip joints you need to have them put back in the same, but what about the vits/trackicks....

also, my rear drums are really farked. rusted and seized. i want to do a disc conversion, but i may not have enough resources to get it done. so i'm just planning on getting the drums over hauled, new cylinder, new pads, and i was told the springs need to be OEM. what a PITA.

thanks
Steve
Logged
1989 Suzuki Vitara... Stock Standard

something closer to home: www.DARWIN4X4.net[/url]

outerlimits4x4.com = Great Tech, Bad Influence
*

Offline lil_Truck

  • 1148
  • 0
  • Gender: Male
  • Eric Gardner
Re: removal of rear tail shaft
« Reply #1 on: January 20, 2005, 01:35:21 PM »
I've just pulled the shaft and installed it anyway it fit.  Have not had a problem.

The drive shaft should be self balanced so the placement shouldent matter.

As for the rear brakes, my drums work ok for me, but I also want to go to disc because the mud tears up the shoes within 8 months.  I've also used a after market spring kit and have had no problems with it.
Logged
e-mail: liltruck|removethispart|@comcast.net
96 Tracker
6" Calimini Lift with custom Frame
32 MTR's Warn 8000i
Front/Rear ARB's Many New Mods soon.
*

Offline mrfuelish

  • *
  • 2862
  • 13
  • Gender: Male
  • you must have a perception problem.
Re: removal of rear tail shaft
« Reply #2 on: January 21, 2005, 06:36:36 AM »
wipe off both ends and look for a DOT.
Logged
1987,1988,1988,1990 samurai's,  1953 m38a1,  1996 x-90,blue.1996 x-90 red.1994 2 door tracker.   only Dead Fish go with the flow.                No Hairy Nosed Wombats were ran over on the trail today.       My ZUK is Xenophobic.
*

mudfkr

Re: removal of rear tail shaft
« Reply #3 on: January 21, 2005, 07:23:38 AM »
Hi Steve,

I've taken mine off lots of time's without marking it and never had any drive line vibes after. Sammys are a little different obviously with the slip shaft on the drive shaft it self.  Try find the grease-able U-joints if you can, they last longer while playing  in the water.

Mudfkr
PS:No updates on the disk's this week as I been to busy hopefully this week coming.
Logged
*

Offline SiKiD_01

  • 574
  • 0
  • Gender: Male
  • Fully Sik, Flying Vit.
Re: removal of rear tail shaft
« Reply #4 on: January 21, 2005, 08:42:55 AM »
thanks guys.

in the shop manual, it says there is a mark already. i will have a look, if its there, good, if not, i dont think i'll worry too much about it.

thanks again.

Steve
Logged
1989 Suzuki Vitara... Stock Standard

something closer to home: www.DARWIN4X4.net[/url]

outerlimits4x4.com = Great Tech, Bad Influence
Pages: [1]   Go Up
« previous next »