Hello Guest
« previous next »
Pages: [1]   Go Down

I need help on a tranny question.

  • 5 Replies
  • 1211 Views

0 Members and 1 Guest are viewing this topic.

*

Offline Mythose

  • 361
  • 0
I need help on a tranny question.
« on: February 01, 2006, 02:58:19 PM »
Ok the moron that had my kik before me " yes moron  he drilled a hole through the head into the block and used a 3/4 inch piece of all thread instead of a head bolt"   FYI  it has a newer rebuilt motor.   any back to the question the afor mentioned moron striped the tranny drain plugs, not the threads, the part that the 3/8ths ratchet goes into.    I talked to a cupple of trany places and
its going to range from 50 to 200 bucks to have them take it out ----- one of the tranny places told me that i should just take a cold chisel and hammer and use that to unscrew the pluge and just replace it with a new one.

what do you guys think?









Logged
All things must start and end, the key is to not let them start and end in the same place.

Other rigs, 84 Sub 305 High output dana 44 front dana 60 rear turbo 350 tranny, 205 gear drive transfer, 10" lift 38.5 swampers
*

Offline takai

  • 907
  • 0
  • Gender: Male
  • Yes, I drove that here. And No, it's not done!
Re: I need help on a tranny question.
« Reply #1 on: February 01, 2006, 03:16:01 PM »
If you are really careful you might be able to get that plug out that way. I have friend over here that is an absolute master at that. Me...I break my hand open on the case after running the cold chisel through my other hand.  ;D
Logged
87 Sammi "Sir Tweak " Rockcrawler 4:1, Mighty Kong , 1.6 16V, Centerforce II, 2" Exhaust, Esteem seats. - Long gone
97 Tracker "Jezebel"  Bone Stock DD

'Cause, I am to misbehave.
*

Offline Skeeter

  • 23
  • 0
  • Gender: Male
Re: I need help on a tranny question.
« Reply #2 on: February 01, 2006, 03:44:58 PM »
Cold chisel & hammer should get you out of trouble.
Logged
*

Offline wildgoody

  • *
  • 8134
  • 67
  • Gender: Male
  • Turbocharged 150HP 1.6L 8V 93MPH 1/4 mile
Re: I need help on a tranny question.
« Reply #3 on: February 01, 2006, 07:00:53 PM »
You could drill a hole in the center and
use a big screw extractor to back it out.

Logged
Real Trucks Are Built, Not Bought,
And Chrome Don't Get Ya Home.  

An armed man is a citizen. An unarmed man is a subject.
*

Offline Mythose

  • 361
  • 0
Re: I need help on a tranny question.
« Reply #4 on: February 01, 2006, 10:12:31 PM »
I was thinking of a bolt extractor so i think what i will do is invest the 90 bucks into a good chisel set and bolt extractor set,  and a case of beer to bribe my buddy with a lift,  and spend an evening to get the bolt out seeing as chisels and extractors are things that you ALWAYS need

thank you and as always the imput is awsome.
Logged
All things must start and end, the key is to not let them start and end in the same place.

Other rigs, 84 Sub 305 High output dana 44 front dana 60 rear turbo 350 tranny, 205 gear drive transfer, 10" lift 38.5 swampers
*

Offline mrfuelish

  • *
  • 2862
  • 13
  • Gender: Male
  • you must have a perception problem.
Re: I need help on a tranny question.
« Reply #5 on: February 01, 2006, 11:02:51 PM »
You could just weld a long bolt to it and then just use a wrench on it!
Logged
1987,1988,1988,1990 samurai's,  1953 m38a1,  1996 x-90,blue.1996 x-90 red.1994 2 door tracker.   only Dead Fish go with the flow.                No Hairy Nosed Wombats were ran over on the trail today.       My ZUK is Xenophobic.
Pages: [1]   Go Up
« previous next »