Hello Guest
« previous next »
Pages: [1]   Go Down

Where to install a mechanical Oil Pressure gauge on a sami?

  • 6 Replies
  • 2021 Views

0 Members and 2 Guests are viewing this topic.

*

Offline Fordota

  • 40
  • 0
Where to install a mechanical Oil Pressure gauge on a sami?
« on: October 23, 2008, 03:10:44 PM »
I asked this before a little premature and now I cant find where. Anyhow where would I plug my mechanical oil pressure gauge in? I thought I was told that it was above the filter where the wires connect on the drivers side.
Logged
*

Offline ROSS

  • *
  • 1412
  • 0
  • Gender: Male
  • WHY TAKE A PICTURE WHEN YOU CAN DRIVE OVER IT
Re: Where to install a mechanical Oil Pressure gauge on a sami?
« Reply #1 on: October 23, 2008, 03:47:08 PM »
thats the place
Logged
87 SAMI 1600 FUEL INJ. , TORQUER CAM, 6.5 TO 1T-CASE, 5"SPRINGS SHACKLE REVERSE ,2 BODY LIFT, LOCK-RITES FRONT W/ HEAVY-DUTY AXLES & ARB'S REAR  BFG 31 X10.50 X 16",  EXO SKELLETON,
*

Offline rascott

  • 669
  • 15
  • Gender: Male
  • tread lightly monkeywrench a little
Re: Where to install a mechanical Oil Pressure gauge on a sami?
« Reply #2 on: October 23, 2008, 03:54:06 PM »
i did this on my 1.3L kick.
used an 1/8" brass tee so i still have the idiot light. threads seem close enough. no leaks.
Logged
'89 kick w/little motor, still got pieces of jeff's pucks, stan's sticks into 4.24:1 tcase, 31x10.5x15's, rear lockrite, kick power steering, some radios(kj6esv), bmw seat, other changes just because. done on the cheap.
suzi the psychic gets me fishing.
*

Offline Rhinoman

  • 4502
  • 36
  • Gender: Male
  • Bend it, Break it, Fix it
    • Rhinoman
Re: Where to install a mechanical Oil Pressure gauge on a sami?
« Reply #3 on: October 24, 2008, 09:49:41 AM »
It should be an M10 x 1.0mm fitting, you can buy adapters.
Logged
2000 Vitara 1.6, 3+3 Lift, 33"MTs, 5:83s, LWB brakes, Winch, Snorkel, Safari Rack
1986 SJ413K PickUp, 1.6L conversion.

OBD1 - Full diagnostics on a PC/Laptop: http://www.rhinopower.org
*

Offline rascott

  • 669
  • 15
  • Gender: Male
  • tread lightly monkeywrench a little
Re: Where to install a mechanical Oil Pressure gauge on a sami?
« Reply #4 on: October 24, 2008, 01:38:56 PM »
Quote from: Rhinoman on October 24, 2008, 09:49:41 AM
It should be an M10 x 1.0mm fitting, you can buy adapters.
i'm sure you are right, and i've wondered how much difference there is from npt sizes.
i've done this many times over the years with japanese and german engines. doesn't seem to stretch or pull threads.
mabe.
my experience.
Logged
'89 kick w/little motor, still got pieces of jeff's pucks, stan's sticks into 4.24:1 tcase, 31x10.5x15's, rear lockrite, kick power steering, some radios(kj6esv), bmw seat, other changes just because. done on the cheap.
suzi the psychic gets me fishing.
*

Offline Fordota

  • 40
  • 0
Re: Where to install a mechanical Oil Pressure gauge on a sami?
« Reply #5 on: October 26, 2008, 03:10:14 PM »
Thanks for the help guys! Just one more... When I remove the dummy light sensor above the oil filter, will it be a male that comes out of a female port in the block?
Logged
*

Offline rascott

  • 669
  • 15
  • Gender: Male
  • tread lightly monkeywrench a little
Re: Where to install a mechanical Oil Pressure gauge on a sami?
« Reply #6 on: October 26, 2008, 04:32:35 PM »
yes
in my case i used an 1/8" brass nipple to the tee, screwed the sender in one end and the compression fit tube in the other.
Logged
'89 kick w/little motor, still got pieces of jeff's pucks, stan's sticks into 4.24:1 tcase, 31x10.5x15's, rear lockrite, kick power steering, some radios(kj6esv), bmw seat, other changes just because. done on the cheap.
suzi the psychic gets me fishing.
Pages: [1]   Go Up
« previous next »